Shop By
Shopping Options

Home Repair

Outdrive and Sterndrive Repair

Outdrive and sterndrive repair in Long Beach for MerCruiser, Volvo Penta, OMC and Yamaha: bellows, seals, gimbals and lower units. Get a quote.

  • 4 services
  • At your slip or in the shop
We can't find products matching the selection.

Sterndrive and Outdrive Repair in Long Beach and San Pedro

We repair and service sterndrives, including MerCruiser and Volvo Penta outdrives, at your slip, dock or storage yard from Marina del Rey to Newport Beach, or at our San Pedro shop.

What the work covers

Bellows, gimbal bearing and lower unit work, gear lube changes included, is done with the boat out of the water: on its trailer, in a storage yard, at our shop or after a haul-out, which is the yard's charge and is listed on your estimate. Parts are quoted with the job, and repairs found during a check are quoted before any work is done.

Signs your outdrive needs attention

  • Milky gear lube, or metal flakes on the drain plug
  • Water in the bilge near the transom
  • A rumble or grinding that changes with engine speed
  • Hard or noisy shifting
  • The drive will not trim up, or slowly drifts down

Questions about outdrive repair

Why is my gear lube milky?

Milky lube means water is getting into the drive, often past a worn seal. A pressure test finds the leak, and a lower unit reseal fixes it. Running the drive with water in the lube wears the gears and bearings.

How often should the bellows be replaced?

Follow your drive maker's interval, and replace them sooner if you see cracks or dry, stiff rubber. A failed bellows can let water into the boat, so they deserve a look whenever the drive is serviced.

Book a visit: submit a ticket with the boat, where it is kept and what the drive is doing, or call our number.

See also: sterndrive bellows and gimbal bearing signs they need service.

Questions

Items 21 to 29 of 29 total

Page
Show per page
  1. #603 Common question asks Dec 14, 2025

    What is a lower unit reseal and when is it necessary?

    1. Fryderyk Florczak answers Dec 14, 2025

      A lower unit reseal involves replacing worn or damaged seals that protect the gearcase from water intrusion. It becomes necessary if water is found in the gear oil, seals are leaking, or after propeller shaft damage. Resealing helps prevent internal corrosion and costly gear failure.

  2. #589 Common question asks Dec 14, 2025

    What is a raw water impeller and why is it critical for my engine?

    1. Fryderyk Florczak answers Dec 14, 2025

      The raw water impeller is a rubber rotor inside the seawater pump that pulls cooling water from the ocean or lake into your engine. If it fails, the engine can overheat within minutes, leading to serious damage such as warped heads or exhaust system failure. Regular impeller replacement is essential for engine reliability.

  3. #93 Common question asks Jun 20, 2025

    Do you offer a warranty on outdrive repairs?

    1. Lukas answers Jun 20, 2025

      Yes. Our workmanship is warranted for 90 days from the invoice date; new parts carry their manufacturer's warranty. Your dated invoice lists the work and the parts, a useful record for maintenance and resale.

  4. #91 Common question asks Jun 20, 2025

    Can you pressure test my outdrive for leaks?

    1. Lukas answers Jun 20, 2025

      Yes – we perform pressure and vacuum testing to check for internal seal failure. It's a crucial step before refilling with gear oil or reinstalling the drive.

  5. #89 Common question asks Jun 20, 2025

    Do you replace bellows and U-joints on stern drives?

    1. Lukas answers Jun 20, 2025

      Yes. With the boat out of the water, we replace the bellows, U-joints, gimbal bearings, shift cables, trim senders and seals that keep water out and the drive working.

  6. #87 Common question asks Jun 20, 2025

    How much does it cost to repair an outdrive?

    1. Lukas answers Jun 20, 2025

      Labor is $150 an hour, plus the trip fee for work at your boat ($30 in San Pedro up to $110 in Newport Beach). An annual drive service or a minor seal job usually takes 2-4 hours; bellows, gimbal bearing and rebuild jobs take longer. You get a written estimate for labor, parts and the trip fee before any work starts, and any haul-out or yard charge is listed on it too.

  7. #85 Common question asks Jun 20, 2025

    Do you offer on-site outdrive removal and repair?

    1. Lukas answers Jun 20, 2025

      Yes, wherever the boat is out of the water: on a trailer, a lift or at a boatyard. An outdrive must never come off while the boat is afloat, so a boat in a slip is hauled out first, and the yard's charge is listed on your estimate. Most seal kits and gear lube changes are done on-site, and major rebuilds may go to our shop.

  8. #83 Common question asks Jun 20, 2025

    What are signs that my outdrive needs repair?

    1. Lukas answers Jun 20, 2025

      Watch for water in the gear oil, excessive vibration, shifting issues, grinding noises, or visible oil leaks near the bellows or prop. These are warning signs that your outdrive needs service ASAP.

  9. #81 Common question asks Jun 20, 2025

    Do you repair MerCruiser and Volvo Penta outdrives?

    1. Lukas answers Jun 20, 2025

      Yes, we specialize in MerCruiser Alpha/Bravo and Volvo Penta SX/DPH outdrives. We handle everything from seal replacement and gear lube leaks to complete overhauls and resealing jobs.

Items 21 to 29 of 29 total

Page
Show per page