Boat Engine Repair
Boat engine repair in Long Beach and San Pedro for Mercury, Volvo Penta, Indmar, Yanmar, Cummins and more, from diagnostics to rebuilds. Get a quote.
- 5 services
- Labor $150/hr
- Trip fee from $30
- At your slip or in the shop
Boat Engine Repair in Long Beach and San Pedro
We find and fix boat engine problems, from hard starting and overheating to lost power. We work on Mercury, MerCruiser, Yamaha, Volvo Penta, Indmar, Yanmar and Cummins engines at your slip, dock or storage yard from Marina del Rey to Newport Beach, or at our San Pedro shop.
What the work covers
- Diagnosis and repair: marine engine repair starts with finding the cause, tracing the problem through fuel, ignition, compression and cooling.
- Overheating: overheating diagnosis and a cooling system flush. Common causes are a worn raw-water impeller, a clogged heat exchanger, a stuck thermostat or scale in the cooling passages.
- Exhaust: exhaust riser and elbow replacement when corrosion or leaks put the engine at risk of taking on water.
- Scheduled service: a 100-hour service or annual engine maintenance at your engine maker's interval. It typically covers oil and filters, fuel filters, the impeller and belts, plus a look at hoses, clamps and anodes.
- Valves and compression: valve adjustment and compression testing. Many engines need valve clearance set on a schedule, and compression numbers show the condition of the rings and valves.
When to call
- The engine cranks but will not start, or starts and dies
- The temperature gauge climbs or the overheat alarm sounds
- Rough idle, misfires or hesitation when you throttle up
- Lost top speed or RPM
- Smoke, a new noise or a fuel smell; with a fuel smell, leave the engine off and air out the boat
Questions about boat engine repair
Can you check my engine where the boat is kept?
Yes. We come to your slip, dock or storage yard from Marina del Rey to Newport Beach. If the check turns up a repair, we quote it before any work is done.
When does a repair turn into a rebuild?
When a compression test and inspection show wear across the engine, such as low compression on several cylinders, heavy oil use or damage from water or overheating. In that case we explain the rebuild option and quote it.
Book a visit: submit a ticket with the boat, where it is kept and what the engine is doing, or call (562) 542-7296.
Is your boat struggling to start, losing power, or overheating? Our marine engine repair service in Long Beach and San Pedro identifies and fixes the problem. We diagnose issues with fuel, ignition, compression, and cooling systems, including worn raw-water impellers, clogged heat exchangers, stuck thermostats, and scale buildup. From diagnosis to exhaust system repairs, we get your boat running smoothly again.
Marine Engine Repair: FAQ
What is involved in a marine engine repair?
Our process starts with a thorough examination of the fuel, ignition, compression, and cooling systems to pinpoint the cause of the problem. We then perform any necessary repairs or replacements, including cleaning or replacing raw-water impellers, heat exchangers, thermostats, or exhaust components.
Can you repair my boat's engine at its slip or in a storage yard?
Yes, our mobile service team comes to your boat wherever it is moored – from Marina del Rey to Newport Beach – so you don't need to trailer or transport it to a shop. We also have a San Pedro shop for larger projects and more extensive repairs.
See also: marine engine thermostat problems stuck open vs closed.
See also: boat engine overheating diagnosis order and cooling flush.
-

#910 Common question asks
What is an exhaust riser and why might it need replacement?
-

The exhaust riser connects your engine’s exhaust manifold to the exhaust system, directing engine gases out of the boat. Over time, it can corrode or crack due to heat and saltwater exposure, which can lead to leaks, reduced engine performance, or water entering the engine.
-
-

#908 Common question asks
Do you provide documentation and recommendations after testing?
-

Yes. You get the compression reading for every cylinder, notes on valve clearances and our recommendations, useful for maintenance planning and for showing a buyer the engine's condition. It is a mechanic's report, not a marine survey; insurers and lenders often require a survey by an accredited marine surveyor.
-
-

#906 Common question asks
Can a compression test help prevent major engine failure?
-

It can help. A compression test shows internal wear early, so it can be dealt with before it leads to a major failure. Catching a problem early usually costs much less than a rebuild or replacement.
-
-

#904 Common question asks
What is included in your valve adjustment and compression testing service?
-

Our service includes checking and adjusting valve clearances to the maker's specifications, a compression test on every cylinder, and a written record of the results. If a reading is abnormal, we tell you what it points to and what we recommend.
-
-

#902 Common question asks
Can improper valve adjustment cause engine starting problems?
-

Yes. Valves that are too tight or too loose can affect compression and combustion, leading to hard starting, misfires and poor throttle response. When lash is the cause, setting it correctly brings back easy starting; if the engine still starts hard, we look at fuel, glow plugs and compression next.
-
-

#900 Common question asks
How often should valves be adjusted on a marine engine?
-

It depends on the engine maker and model, and the intervals vary widely, so follow the schedule in your owner's manual. Tell us your engine model and we will check its schedule.
-
-

#898 Common question asks
What does a compression test tell me about my engine’s condition?
-

A compression test measures the pressure inside each cylinder to evaluate engine health. Low or uneven compression can indicate worn valves, piston rings, or head gasket issues. This test helps diagnose problems before they turn into costly repairs.
-
-

#896 Common question asks
What is valve adjustment and why is it important for marine engines?
-

Valve adjustment resets the small gap (valve lash) between the rocker arm and the valve stem to the engine maker's spec, so the valves open and close at the right time. Wrong clearance causes power loss, noise, rough running and, if too tight, burned valves.
-
-

#218 Common question asks
What if the starter engages but the engine will not turn at all?
-

That usually points to a weak battery or a poor connection, a starter that has failed, or an engine that is seized or has water in a cylinder. Do not keep cranking it: we test the batteries, cables and starter and check whether the engine turns by hand, then give you a written estimate for the repair.
-
-

#216 Common question asks
Can you bring back a diesel engine that has been sitting for years?
-

Often, yes. We start with a compression test and a check of the fuel, starting and cooling systems, then tell you what can be repaired and what needs replacing, with a written estimate. Old fuel is drained and disposed of, and the fuel system cleaned, before the engine is started.
-





