Bilge Pump Repair
Bilge pump repair and replacement in Long Beach and San Pedro: pumps, float switches, high-water alarms and bilge cleaning. Book a mobile visit.
- 3 services
- Labor $150/hr
- Trip fee from $30
- At your slip or in the shop
Bilge Pump Repair in Long Beach and San Pedro
We repair and test bilge pumps, float switches and high-water alarms at your slip, dock or storage yard from Marina del Rey to Newport Beach. The bilge pump protects the boat while you are away, so it has to switch on by itself and keep working.
What the work covers
- Bilge system hygiene and pump defense: inspection, cleaning and repair of the bilge, the pump, its hose and check valve, and the wiring and fuse.
- Automatic float switch replacement when the switch sticks or no longer turns the pump on.
- High-water alarm safety systems: installation and testing of an alarm that sounds when water rises above the normal pump level.
We also check the pump's power feed, so the automatic circuit works while you are not aboard. If water is coming in through a damaged hull, the repair goes to a boatyard; fiberglass repair covers the small, non-structural repairs we do. If the boat is taking on water or anyone is in danger, call the Coast Guard on VHF channel 16 or 911 first. Parts are quoted with the job.
When to call
- The pump runs often, or cycles when it has not rained
- The pump runs nonstop, or stays off when you lift the float
- More water than usual in the bilge
- An oily sheen or a bad smell from the bilge
- Corroded wires or connectors at the pump
- A high-water alarm that sounds, or one that has never been tested
Questions about bilge pumps
Why does my bilge pump keep cycling?
Water is getting in from somewhere. Common sources are the shaft seal, hose connections, through-hull fittings, deck drains and rain. A check valve that leaks back can also make the pump cycle. We trace the source during the bilge inspection.
Do I need a high-water alarm if I have an automatic pump?
The alarm warns you when the pump has failed or cannot keep up with the water coming in. Without one, the first sign of trouble may be a boat sitting low at the dock.
Book a visit: submit a ticket with the boat, where it is kept and what the bilge pump is doing, or call (562) 542-7296.
See also: fiberglass boat repair at the slip cracks chips and leaks.
-

#748 Common question asks
How is the automatic float switch replaced?
-

We remove the old switch, inspect the wiring and pump, and install a quality marine replacement on a fused circuit. After installation we flood-test the bilge to confirm the new switch turns the pump on and off correctly.
-
-

#746 Common question asks
Can a faulty float switch cause my boat to sink?
-

Yes. A malfunctioning float switch can keep the bilge pump from turning on, which lets water build up. Regular inspection and timely replacement help avoid flooding. If the boat is taking on water or anyone is in danger, call the Coast Guard on VHF channel 16 or 911 first.
-
-

#744 Common question asks
How do I know if my float switch needs replacement?
-

Common signs include the bilge pump not activating, intermittent operation, or physical damage to the switch. We also test the switch’s response and continuity during inspection to ensure it’s fully operational.
-
-

#742 Common question asks
What is an automatic float switch and why is it important?
-

An automatic float switch senses the water level in your bilge and turns the bilge pump on when needed, even when nobody is aboard. It keeps rainwater and small leaks from building up and damaging the engine and electronics.
-
-

#148 Common question asks
Do repairs come with a warranty?
-

Yes. Our workmanship is warranted for 90 days from the invoice date; new pumps and switches carry their manufacturer's warranty.
-
-

#146 Common question asks
What should I do if my bilge pump fails and water is rising?
-

If the boat is taking on water or anyone is in danger, call the Coast Guard on VHF channel 16 or 911 first, then your marina or harbor patrol. To repair a failed bilge pump, float switch or wiring, call us at (562) 542-7296: we fit urgent repairs in as soon as we can, Monday to Saturday, 8 AM to 6 PM.
-
-

#144 Common question asks
Do you install backup or high-water alarms in the bilge?
-

Yes. We install secondary pumps, high-water alarms and battery backups. They give you extra protection if the main pump fails or a leak outpaces it.
-
-

#142 Common question asks
How much does it cost to repair a bilge system?
-

Labor is $150 an hour, plus parts and the trip fee for work at your boat. A pump or float switch replacement usually takes 1-2 hours; rewiring and full bilge cleaning depend on the boat and are quoted after we look. You get a written estimate before any work starts.
-
-

#140 Common question asks
Can you clean and disinfect the bilge area?
-

Yes – we offer full bilge cleaning, including removal of sludge, oil residue, and mold. We use marine-safe cleaners to sanitize the bilge and improve pump performance and odor control.
-
-

#138 Common question asks
What are signs that my bilge system isn’t working properly?
-

If you notice standing water, a musty smell, pump cycling constantly, or no response from the float switch, your bilge system needs inspection. We recommend servicing it before the problem becomes serious.
-



