Home Repair

Propeller and Shaft Repair

Propeller and prop shaft repair in Long Beach and San Pedro: dings, spun hubs, re-hubbing, shaft alignment and cutless bearings. Get a quote.

  • 3 services
  • Labor $150/hr
  • Trip fee from $30
  • At your slip or in the shop
View as Grid List

3 Items

Set Descending Direction
  1. Prop Shaft Alignment & Cutless Bearing Replacement
    Rating:
    100%
    $150 /hr
    Usually 4–8 hours
  2. Propeller Pulling & Re-Hubbing Service
    Rating:
    100%
    $150 /hr
    Usually 1–2 hours
per page

Propeller and Shaft Repair in Long Beach and San Pedro

We handle propeller and prop shaft work for outboard, sterndrive and inboard boats; blade repair is done by a prop shop. We work at your slip, dock or storage yard from Marina del Rey to Newport Beach, or at our San Pedro shop.

What the work covers

  • Propeller repair: propeller repair brings back blade shape, pitch and balance after a strike, so the prop pushes the boat the way it should. We remove the prop, a prop shop we work with or refer you to repairs it, and we refit it.
  • Stuck props and hubs: propeller pulling and re-hubbing. A seized inboard prop comes off the shaft with a proper puller; that is done with the boat out of the water, or by a diver we refer you to. Outboard and sterndrive props get a new hub when the old one slips.
  • Shafts and bearings: prop shaft alignment and cutless bearing replacement. A worn cutless bearing in the strut or a shaft out of line causes vibration and wears the shaft seal and transmission parts. Cutless bearing work needs the boat out of the water, or a diver we refer you to.

Parts are quoted with the job, and so are any haul-out, diver or prop shop charges; anything we find during the check is quoted before any work is done.

Signs your prop or shaft needs attention

  • New vibration at cruising speed
  • RPM climbs and the boat does not speed up
  • Dings, bends or missing chunks on the blades
  • Lost top speed or higher fuel use
  • A clunk or rumble from the shaft area

Questions about propeller repair

Why does my engine rev up while the boat barely speeds up?

On outboards and sterndrives, a spun hub is a common cause, often after the prop hits something. The hub inside the prop slips, so the engine revs while the prop does not keep up. Re-hubbing fixes it. If the hub is fine, the problem may be in the drive. See outdrive repair.

Is a small ding worth fixing?

Often, yes. Even a small bend changes how the blade loads and can cause vibration. Over time that vibration wears bearings and seals in the drive or transmission, so fixing it early protects those parts.

Book a visit: submit a ticket with the boat, where it is kept and what you feel at the helm, or call (562) 542-7296.

See also: spun prop hub signs causes and when to re hub a propeller.

Questions

Items 11 to 20 of 21 total

Page
Show per page
  1. #1152 Common question asks Dec 20, 2025

    Can propeller removal damage the shaft or seals?

    1. Fryderyk Florczak answers Dec 20, 2025

      If done incorrectly, yes. We use proper marine pullers and techniques to safely remove the propeller without damaging the shaft, keyway, or shaft seals.

  2. #1150 Common question asks Dec 20, 2025

    What are signs of a spun or failing prop hub?

    1. Fryderyk Florczak answers Dec 20, 2025

      Common signs include sudden loss of thrust, inconsistent speed, high RPM with little movement, or vibration. A hub inspection confirms whether re-hubbing is required.

  3. #1148 Common question asks Dec 20, 2025

    What is propeller re-hubbing and when is it needed?

    1. Fryderyk Florczak answers Dec 20, 2025

      Re-hubbing applies to outboard and sterndrive propellers, which have a rubber or plastic hub between the blades and the shaft; when it slips, the engine revs up but the boat barely speeds up. Insert-type hubs can be swapped at the boat, while pressed-in rubber hubs are replaced by a prop shop with a press. Inboard propellers have no hub to replace: they are keyed to a tapered shaft, and we pull them, with the boat out of the water, for shaft, seal or cutless bearing work.

  4. #1146 Common question asks Dec 20, 2025

    Why would I need my propeller pulled off the shaft?

    1. Fryderyk Florczak answers Dec 20, 2025

      Propeller removal is needed for inspections, shaft seal work, cutless bearing replacement or propeller repairs; on an inboard it is done with the boat out of the water. Pulling with a proper puller avoids damaging the shaft and lets the prop go back on correctly.

  5. #316 Common question asks Jun 22, 2025

    Can you remove and reinstall the prop at the marina?

    1. Lukas answers Jun 22, 2025

      On an outboard or a sterndrive, yes: with the drive tilted up we take the prop off at the slip and refit it after a prop shop repairs it. An inboard prop is under the boat, so it comes off on a trailer, after a haul-out or by a diver we refer you to.

  6. #314 Common question asks Jun 22, 2025

    Do you offer propeller balancing to reduce vibration?

    1. Lukas answers Jun 22, 2025

      Yes. A propeller shop balances repaired props before they go back on, which reduces vibration and is easier on the drive and gearbox.

  7. #312 Common question asks Jun 22, 2025

    How do I know if I need to replace the prop instead of repairing it?

    1. Lukas answers Jun 22, 2025

      Replace the prop when blades are broken or badly cracked, a lot of blade material is missing, or the repair would cost close to a new prop. A spun hub can usually be fixed by replacing the hub. If you need a new prop, we help you pick the right diameter and pitch.

  8. #310 Common question asks Jun 22, 2025

    How much does it cost to repair a damaged propeller?

    1. Lukas answers Jun 22, 2025

      Labor is $150 an hour, plus a one-way trip fee by distance for work at your boat ($30 in San Pedro up to $110 in Newport Beach). Removing and refitting a prop usually takes 1-2 hours; the prop shop's repair charge depends on the material and the damage, and a badly cracked or broken prop may need replacing. You get a written estimate before any work starts.

  9. #308 Common question asks Jun 22, 2025

    Do you repair stainless steel and aluminum boat props?

    1. Lukas answers Jun 22, 2025

      Yes, both aluminum and stainless steel. We remove your prop, send it to a propeller repair shop for reshaping, welding if needed, and balancing, and refit it when it comes back. The prop shop's charge is part of your written estimate.

  10. #306 Common question asks Jun 22, 2025

    Can a damaged propeller affect my fuel efficiency and handling?

    1. Lukas answers Jun 22, 2025

      Yes. Even minor dings or bends reduce efficiency and put strain on the drivetrain. A prop restored to its proper shape and balance helps fuel economy, acceleration and steering response.

Items 11 to 20 of 21 total

Page
Show per page