Exhaust Manifold and Riser Repair
Exhaust manifold, riser and elbow repair in Long Beach and San Pedro for MerCruiser, Volvo Penta, Indmar and marine diesels. Get a quote.
- 2 services
- Labor $150/hr
- Trip fee from $30
- At your slip or in the shop
Exhaust Manifold and Riser Repair in Long Beach and San Pedro
We inspect, repair and replace exhaust manifolds, risers and elbows on inboard and sterndrive engines. We work at your slip, dock or storage yard from Marina del Rey to Newport Beach, or at our San Pedro shop.
What the work covers
On many marine engines, seawater runs through the exhaust manifolds and risers to cool them, then leaves with the exhaust. In salt water these parts corrode from the inside, so they can look fine and still be close to failing.
- Manifolds and risers: exhaust manifold repair covers inspection, new gaskets, and repair or replacement of corroded manifolds and risers. Parts are quoted with the job.
- Flappers and shutters: exhaust flapper and shutter service. These valves help stop water from running back into the engine, and they wear out with age.
- Elbows and cooling: riser and elbow replacement and overheating diagnosis are part of our boat engine repair work.
Signs of a manifold or riser problem
- Rust streaks or weeping at the manifold or riser joints
- Overheating, or a hot spot on a manifold or riser
- Water on the spark plugs, or milky oil
- Rough running for the first minutes after a start
- An exhaust smell in the engine compartment or cabin: shut the engine down and get everyone into fresh air
Questions about exhaust manifolds and risers
How often should manifolds and risers be checked?
Follow your engine maker's interval. Boats kept in salt water often need a closer look, since corrosion inside cannot be seen from outside. A check at the annual service is a good habit.
Can a failed riser damage the engine?
Yes. Water that runs back through a failed riser, manifold or gasket can reach the cylinders and rust the valves and rings. Caught early, the fix may be new exhaust parts. Caught late, the engine may need an engine rebuild.
Book a visit: submit a ticket with the boat, where it is kept and what you are seeing, or call (562) 542-7296.
See also: marine exhaust manifolds and risers signs of failure and fixes.
See also: boat engine overheating diagnosis order and cooling flush.
-

#232 Common question asks
Do you service MerCruiser and Volvo Penta exhaust systems?
-

Yes. We repair and replace exhaust manifolds, risers and elbows on MerCruiser, Volvo Penta, Crusader and other inboard and sterndrive engines, using the maker's parts or quality aftermarket kits with stainless hardware. The parts are listed on your written estimate.
-
-

#230 Common question asks
Is it safe to run my engine with a leaking exhaust manifold?
-

No. A leaking manifold or riser can let exhaust, including carbon monoxide, into the boat, or water into the cylinders, which can ruin the engine. Don't run it until it has been checked. We inspect it and give you a written estimate; once you OK it, we schedule the repair as soon as the parts are in.
-
-

#228 Common question asks
Can you repair saltwater-corroded exhaust manifolds?
-

A corroded manifold is usually replaced rather than repaired, because the rust is inside the water passages of the casting. We take it off and inspect it: if the casting and passages are sound, cleaning and new gaskets can be enough; if not, we quote a replacement.
-
-

#226 Common question asks
How much does exhaust manifold repair or replacement cost?
-

Labor is $150 an hour, plus parts and the trip fee for work at your boat. Replacing manifolds and risers usually takes 4-8 hours, and the parts depend on your engine. We inspect first and give you a written estimate before any work starts.
-
-

#224 Common question asks
Do you replace both the exhaust manifold and riser/elbow?
-

We always inspect the full exhaust system, including manifolds, risers, gaskets, and hardware. If one part is failing, the other often is too. We recommend complete kits to avoid repeat repairs.
-
-

#222 Common question asks
Can a bad exhaust manifold cause overheating or loss of power?
-

Yes. Corrosion inside a manifold or riser restricts the cooling water and exhaust flow, which can cause overheating, power loss and, in bad cases, warped cylinder heads. We find the restriction and replace the parts that are blocked or cracked, with a written estimate first.
-
-

#220 Common question asks
What are the signs of a leaking exhaust manifold on a boat?
-

Signs include ticking noises at startup, exhaust fumes in the engine bay, rust streaks, or engine misfires. A leaking manifold can cause engine damage – we test and reseal or replace as needed.
-


